-
Welcome to N-cars.net - the largest Hyundai N car forum. Check out the model specific sections below and scroll down for country specific forums. Scroll down for i30 N, Ioniq 5 N, i20 N, Veloster N and Kona N forums! Check out the i30 N Bible Here!
Suspension and Chassis TURBO TECH RACING/Upper (AVAILABLE) & Lower Motor Mounts for Veloster N and i30N!!
- Thread starter R Veloster N
- Start date
More shipped today and more in stock. We appreciate everyone who has ordered. Spread the word, help others make the best choice in their mount purchase and if you would share it on social media 
Arrived at last. USPS delays aside, quality bit of engineering. Thanks TurboTechRacing.
I'll let you know if the first one despatched arrives. Currently in Brazil i believe
I'll let you know if the first one despatched arrives. Currently in Brazil i believe
Wish I went blue after seeing yours!!Arrived at last. USPS delays aside, quality bit of engineering. Thanks TurboTechRacing.
I'll let you know if the first one despatched arrives. Currently in Brazil i believe
View attachment 13887View attachment 13888View attachment 13889
Pretty crazy the first mount shipped 6 weeks ago and usps mis shipped it on a plane to Brazil. I am sure it will show up to you, but takes another 2 months. Usps won’t stand behind their mistakes and we take their falls! Glad the 2nd one we shipped showed up in normal time.Arrived at last. USPS delays aside, quality bit of engineering. Thanks TurboTechRacing.
I'll let you know if the first one despatched arrives. Currently in Brazil i believe
View attachment 13887View attachment 13888View attachment 13889
Curious, and others too, duties/taxes much they charged? Convert to US funds if you know what it is...I'll let you know if it arrives. Sounds like Dan wants a blue one
If you could locate a local wanting one, if it shows up, we could recoup some of the cost of the mount...
Wow! As value was marked at $200 USA....
Thanks for sharing.
Well just installed my lower mount and I didn't recognize any noticable nvh. Definitely pulls smoother and harder. Made 2nd chirp on a corner under hard acceleration. All 
here!
here!Let’s see some installed photosWell just installed my lower mount and I didn't recognize any noticable nvh. Definitely pulls smoother and harder. Made 2nd chirp on a corner under hard acceleration. All
Here is my upper now fitted.
One thing I did notice. Is I seem to be having an issue on the lower where it is rubbing?
Dan
Being a double bushing design, it maybe rubbing/touching, but being the square bushing is still isolating the drivetrain to the frame, I doubt you feel this though the car? It does fit close between the mounting bracket.
Being a double bushing design, it maybe rubbing/touching, but being the square bushing is still isolating the drivetrain to the frame, I doubt you feel this though the car? It does fit close between the mounting bracket.
Last edited:
Looking back on R Veloster N photo, his was close/touching at this point also during his test fit, but no comment about this was made.
Is that bracket on the transmission, only come down on the left/driver side? Or is it come down on the right/passenger side also?
R Veloster N or Dan can you let us know?
Photo from R Veloster N:
Is that bracket on the transmission, only come down on the left/driver side? Or is it come down on the right/passenger side also?
R Veloster N or Dan can you let us know?
Photo from R Veloster N:
Last edited:
@R Veloster N @Dan_bush27
Please see above 2 post, please advise (photo if possible) on passenger side if there is a clearance issue? Photo would be best.
I think we can machine the face down on that part that is touching, so the "offset" is smaller (not so wide), and allows room on the side that has those 2 bolts, holding the mount together. I think we can machine off that face .100"/2.5 MM, which should be plenty of room, as the front of the mount holds it centered in that bracket.
Please see above 2 post, please advise (photo if possible) on passenger side if there is a clearance issue? Photo would be best.
I think we can machine the face down on that part that is touching, so the "offset" is smaller (not so wide), and allows room on the side that has those 2 bolts, holding the mount together. I think we can machine off that face .100"/2.5 MM, which should be plenty of room, as the front of the mount holds it centered in that bracket.
It is touching, I’ve not had mine down off the jack stands waiting for other parts. Sorry about not saying anything but I didn’t consider it a real issue. Milling down the face will solve the issue. 
I’ll send you photos tomorrow.
I’ll send you photos tomorrow.
Last edited:
Sounds good, we are out and making 25 more so good timingIt is touching, I’ve not had mine down off the jack stands waiting for other parts. Sorry about not saying anything but I didn’t consider it a real issue. Milling down the face will solve the issue.
I’ll send you photos tomorrow.
As stated it does just barely touch. More or less just looks like some paint rub.
However the main square bushing still 100% isolates the transmission to the frame.