It is the one that goes straight down. You either need a long, and I mean longer than a standard Halfords one, posidrive screwdriver, or you can get a ratchet spanner direct on the hex head off the adjuster. It's a long time ago I did mine so can't remember the size.
-
Welcome to N-cars.net - the largest Hyundai N car forum. Check out the model specific sections below and scroll down for country specific forums. Scroll down for i30 N, Ioniq 5 N, i20 N, Veloster N and Kona N forums! Check out the i30 N Bible Here!
I20N headlights
- Thread starter tc222
- Start date
The screw is hidden behind the metal plate on the back of the headlight. The metal plate is secured by a screw. Undo the screw just enough for you to be able to flip the plate out of the way.
Thank you for your answer frenchy2475.
I took a picture for you to check the right screw for me please.
So if I get it right i have to unscrew the srew pointed by the blue arrow and afterwards remove the metallic tablet to
be ablle to reach the screw pointed with the red arrow?
No problem, will give you much more long range. I don’t think the lights are as bad as people make out. They just need correctly adjusting. I have driven cars with much poorer lights.
Yes, i do think so too.No problem, will give you much more long range. I don’t think the lights are as bad as people make out. They just need correctly adjusting. I have driven cars with much poorer lights.
The lights are good by design, i believe it's all about adjustments to work properly.
I will give you feedback as soon as possible.
Thanks again frenchy!
That adjusts the dip beam only. The main beam is harder to get to and hidden by the cover plate you can see in the post above.
You would think, given the trouble they've gone to hiding it, that it would have been accurately set at the factory but mine was so low it was dangerous. Now it's perfect but only because I did it myself. The Hyundai service department was clueless and could only mess with the dip beam trying to get it as high as possible to compensate.
Last edited:
The plate is guide for the screw driver so it engages in the adjuster and does not just twist out. I suspect the fact it covers the other screw is just a byproduct of it's primary function.
There are 2 metal plates and both of them are now in the glove box with the 2 screws in case the next owner is a must have everything original fanatic. They were such a pain to get off they certainly weren't going back on and the alignment is perfect now.
I don’t think those instructions relate to the i20N as they refer to removable headlight bulbs and they are not removable on the i20N.
Wow, Salty for one year on!
If you weren't so busy tyring to be clever, you might note that the i20N manual has all the details in for the LED headlights, the adjustments and the the heights to be set at.
From the factory, mine were set very low and nowhere near where the manual advised. Also, if you actually set them to the height shown in the manual, most drivers coming the other way will flash that you are dazzling them. So they either need to be set slightly lower or drip them down to 1 on the beam level adjustment within the car.
I tell you what, this is a very confusing thread as there seems to be a lot of contradictory information from well meaning contributors!
So, regarding my i20N, if I want to adjust the dipped beam to be a bit higher (not the full beam) do I adjust the knurled wheel (the one that also has a nut head) or a posidrive and move these little plates mentioned above?
So, regarding my i20N, if I want to adjust the dipped beam to be a bit higher (not the full beam) do I adjust the knurled wheel (the one that also has a nut head) or a posidrive and move these little plates mentioned above?
Last edited:
Dipped beam can be adjusted from the top using a posidrive. To adjust the high beams only you need to move the metal plate out of the way. I used a tiny ratchet with a posidrive screwdriver head attached to it to make the adjustment.
Oh, you mean an extra long posidrive? Thank you
. Are we talking three full turns kind of adjustment?When I did mine I marked the existing setting on a vertical surface to show the upper dip cut offs and the centre of the high beams. Then I reset the dip beam cut offs to the correct height for the road which was largely trial and error but you need it to be as high as possible without the chance of dazzling anyone which is about headlight level. Since both beams are on with high beam you then need to set the high beam to fill everything above that upper cut off. So go a bit higher using the vertical surface template and then drop them until they just touch those dip upper cut offs without any gaps.Oh, you mean an extra long posidrive? Thank you
After that mine is now perfect.